Certyfikat ISO , Szkolenie, Audyt, etc. - IKMJISO.org – normy opublikowane w październiku 2015 | | Certyfikat ISO , Szkolenie, Audyt, etc. - IKMJ Certyfikat ISO , Szkolenie, Audyt, etc. - IKMJISO.org – normy opublikowane w październiku 2015 | ISO.org – normy opublikowane w październiku 2015 – Certyfikat ISO , Szkolenie, Audyt, etc. – IKMJ ISO.org – normy opublikowane w październiku 2015 – Certyfikat ISO , Szkolenie, Audyt, etc. – IKMJ
Nowa norma ISO

ISO.org – normy opublikowane w październiku 2015

Nowe normy i standardy opublikowane w październiku 2015 roku:
* Dostępne tylko w języku angielskim

** Francuska wersja standardu wcześniej publikowana wyłącznie w języku angielskim

 

Grupa cenowa
TC 6 Paper, board and pulps
ISO 5631-1:2015 Paper and board — Determination of colour by diffuse reflectance — Part 1: Indoor daylight conditions (C/2 degrees) C
ISO 5631-2:2015 Paper and board — Determination of colour by diffuse reflectance — Part 2: Outdoor daylight conditions (D65/10 degrees) C
ISO 5631-3:2015 Paper and board — Determination of colour by diffuse reflectance — Part 3: Indoor illumination conditions (D50/2 degrees) C
TC 17 Steel
ISO 16143-1:2014 * Stainless steels for general purposes — Part 1: Corrosion-resistant flat products F
ISO 13520:2015 * Determination of ferrite content in austenitic stainless steel castings B
ISO 13521:2015 * Austenitic manganese steel castings A
ISO 16468:2015 * Investment castings (steel, nickel alloys and cobalt alloys) — General technical  requirements B
TC 20 Aircraft and space vehicles
ISO 8267-1:2015 Aircraft —  Tow bar attachment fittings interface requirements — Part 1: Main line aircraft A
ISO 8267-2:2015 Aircraft — Tow bar attachment fittings interface requirements — Part 2: Regional aircraft A
ISO 16682:2015 * Aerospace series — Terminology for clamping devices A
ISO 12208:2015 * Space systems — Space environment (natural and artificial) — Observed proton fluences over long duration at GEO and guidelines for selection of confidence level in statistical model of solar proton fluences B
ISO 17689:2015 * Space systems — Interface control documents between ground systems, ground support equipment and launch vehicle with payload C
ISO/TR 18146:2015 * Space systems — Space debris mitigation design and operation guidelines for spacecraft F
TC 22 Road vehicles
ISO 18541-4:2015 * Road vehicles — Standardized access to automotive repair and maintenance information (RMI) — Part 4: Conformance test G
ISO 7637-1:2015 * Road vehicles — Electrical disturbances from conduction and coupling — Part 1: Definitions and general considerations B
ISO 17409:2015 * Electrically propelled road vehicles — Connection to an external electric power supply — Safety requirements D
ISO 15500-15:2015 * Road vehicles — Compressed natural gas (CNG) fuel system components — Part 15: Gas-tight housing and ventilation hose A
TC 23 Tractors and machinery for agriculture and forestry
ISO 13460-1:2015 * Agricultural irrigation equipment — Plastics saddles — Part 1: Polyethylene pressure pipes B
ISO 18471:2015 * Agricultural irrigation equipment —  Filters — Verification of filtration grade B
TC 34 Food products
ISO 17604:2015 Microbiology of the food chain — Carcass sampling for microbiological analysis C
TC 41 Pulleys and belts (including veebelts)
ISO 283:2015 Textile conveyor belts — Full thickness tensile strength, elongation at break and elongation at the reference load — Test method B
ISO 7622-2:2015 Steel cord conveyor belts — Longitudinal traction test — Part 2: Measurement of tensile strength A
ISO 7623:2015 Steel cord conveyor belts — Cord-to-coating bond test — Initial test and after thermal treatment A
TC 44 Welding and allied processes
ISO 9018:2015 Destructive tests on welds in metallic materials — Tensile test on cruciform and lapped joints B
ISO 17641-2:2015 Destructive tests on welds in metallic materials — Hot cracking tests for weldments — Arc welding processes — Part 2: Self-restraint tests C
TC 45 Rubber and rubber products
ISO 13775-1:2015 * Thermoplastic tubing and hoses for automotive use — Part 1: Non-fuel applications C
ISO 289-3:2015 Rubber, unvulcanized — Determinations using a shearing-disc viscometer — Part 3: Determination of the Delta Mooney value for non-pigmented, oil-extended emulsion-polymerized SBR A
ISO 5893:2002 Rubber and plastics test equipment — Tensile, flexural and compression types (constant rate of traverse) — Specification A
TC 46 Information and documentation
ISO 30302:2015 * Information and documentation — Management systems for records — Guidelines for implementation E
TC 58 Gas cylinders
ISO 9809-1:2010 Gas cylinders — Refillable seamless steel gas cylinders — Design, construction and testing — Part 1: Quenched and tempered steel cylinders with tensile strength less than 1 100 MPa F
ISO 9809-2:2010 Gas cylinders — Refillable seamless steel gas cylinders — Design, construction and testing — Part 2: Quenched and tempered steel cylinders with tensile strength greater than or equal to 1 100 MPa F
ISO 9809-3:2010 Gas cylinders — Refillable seamless steel gas cylinders — Design, construction and testing — Part 3: Normalized steel cylinders F
TC 61 Plastics
ISO 4586-1:2015 * High-pressure decorative laminates (HPL, HPDL) — Sheets based on thermosetting resins (Usually called Laminates) — Part 1: Introduction and general information A
ISO 4586-2:2015 * High-pressure decorative laminates (HPL, HPDL) — Sheets based on thermosetting resins (Usually called Laminates) — Part 2: Determination of properties H
ISO 4586-3:2015 * High-pressure decorative laminates (HPL, HPDL) — Sheets based on thermosetting resins (Usually called Laminates) — Part 3: Classification and specifications for laminates less than 2 mm thick and intended for bonding to supporting substrates C
ISO 4586-4:2015 * High-pressure decorative laminates (HPL, HPDL) — Sheets based on thermosetting resins (Usually called Laminates) — Part 4: Classification and specifications for compact laminates of thickness 2 mm and greater B
ISO 4586-5:2015 * High-pressure decorative laminates (HPL, HPDL) — Sheets based on thermosetting resins (Usually called Laminates) — Part 5: Classification and specifications for flooring grade laminates less than 2 mm thick intended for bonding to supporting substrates B
ISO 4586-6:2015 * High-pressure decorative laminates (HPL, HPDL) — Sheets based on thermosetting resins (Usually called Laminates) — Part 6: Classification and specifications for exterior-grade compact laminates of thickness 2 mm and greater B
ISO 4586-7:2015 * High-pressure decorative laminates (HPL, HPDL) — Sheets based on thermosetting resins (Usually called Laminates) — Part 7: Classification and specifications for design laminates D
ISO 4586-8:2015 * High-pressure decorative laminates (HPL, HPDL) — Sheets based on thermosetting resins (Usually called Laminates) — Part 8: Classification and specifications for alternative core laminates C
TC 67 Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries
ISO 17945:2015 Petroleum, petrochemical and natural gas industries — Metallic materials resistant to sulfide stress cracking in corrosive petroleum refining environments F
ISO 21329:2004 Petroleum and natural gas industries — Pipeline transportation systems — Test procedures for mechanical connectors H
ISO 19901-1:2015 * Petroleum and natural gas industries — Specific requirements for offshore structures — Part 1: Metocean design and operating considerations H
TC 68 Financial services
ISO 18774:2015 * Securities and related financial instruments — Financial Instrument Short Name (FISN) B
TC 70 Internal combustion engines
ISO 7967-10:2014 Reciprocating internal combustion engines — Vocabulary of components and systems — Part 10: Ignition systems B
ISO 7967-11:2014 Reciprocating internal combustion engines — Vocabulary of components and systems — Part 11: Fuel systems D
TC 76 Transfusion, infusion and injection, and blood processing equipment for medical and pharmaceutical use
ISO 15378:2015 Primary packaging materials for medicinal products — Particular requirements for the application of ISO 9001:2008, with reference to Good Manufacturing Practice (GMP) G
TC 86 Refrigeration and air-conditioning
ISO 5149-1:2014/Amd 1:2015 Refrigerating systems and heat pumps — Safety and environmental requirements — Part 1: Definitions, classification and selection criteria — Amendment 1: Correction of QLAV, QLMV XZ
ISO 23953-1:2015 Refrigerated display cabinets — Part 1: Vocabulary A
ISO 23953-2:2015 Refrigerated display cabinets — Part 2: Classification, requirements and test conditions H
TC 87 Cork
ISO 10718:2015 Cork stoppers — Characterization of a low-in-germs stopper, through the enumeration of colony-forming units of yeasts, moulds and bacteria, capable of both being extracted and growing in alcoholic medium A
TC 89 Wood-based panels
ISO 12460-3:2015 Wood-based panels — Determination of formaldehyde release — Part 3: Gas analysis method B
TC 92 Fire safety
ISO 19702:2015 Guidance for sampling and analysis of toxic gases and vapours in fire effluents using Fourier Transform Infrared (FTIR) spectroscopy G
TC 94 Personal safety — Protective clothing and equipment
ISO 16900-6:2015 * Respiratory protective devices — Methods of test and test equipment — Part 6:  Mechanical resistance/strength of components and connections D
ISO 16900-9:2015 * Respiratory protective devices — Methods of test and test equipment — Part 9: Determination of carbon dioxide content of the inhaled gas C
ISO 16900-10:2015 * Respiratory protective devices — Methods of test and test equipment — Part 10: Resistance to ignition, flame, radiant heat and heat D
ISO 16900-13:2015 * Respiratory protective devices — Methods of test and test equipment — Part 13: RPD using regenerated breathable gas and special application mining escape RPD: Consolidated test for gas concentration, temperature, humidity, work of breathing, breathing resistance, elastance and duration B
TC 102 Iron ore and direct reduced iron
ISO/TR 16043:2015 * Iron ores — Determination of chlorine content — X-ray fluorescence spectrometric method C
TC 107 Metallic and other inorganic coatings
ISO 28721-4:2015 * Vitreous and porcelain enamels — Glass-lined apparatus for process plants — Part 4: Quality requirements for glass-lined flanged steel pipes and flanged steel fittings A
ISO 28764:2015 Vitreous and porcelain enamels — Production of specimens for testing enamels on sheet steel, sheet aluminium and cast iron A
TC 108 Mechanical vibration, shock and condition monitoring
ISO 13373-3:2015 Condition monitoring and diagnostics of machines — Vibration condition monitoring — Part 3: Guidelines for vibration diagnosis F
TC 110 Industrial trucks
ISO 5053-1:2015 * Industrial trucks — Terminology and classification — Part 1: Types of industrial trucks H
ISO 11525-2:2015 * Rough-terrain trucks — User requirements — Part 2: Slewing variable-reach trucks C
TC 113 Hydrometry
ISO 26906:2015 * Hydrometry — Fishpasses at flow measurement structures F
TC 114 Horology
ISO 19235:2015 Analogue quartz clocks — Timing accuracy B
TC 121 Anaesthetic and respiratory equipment
ISO 10079-1:2015 Medical suction equipment — Part 1: Electrically powered suction equipment E
TC 126 Tobacco and tobacco products
ISO/TR 19478-2:2015 ISO and Health Canada intense smoking parameters — Part 2: Examination of factors contributing to variability in the routine measurement of TPM, water and NFDPM smoke yields of cigarettes G
ISO/TS 3550-3:2015 * Cigarettes — Determination of loss of tobacco from the ends — Part 3: Method using a vibro-bench B
TC 130 Graphic technology
ISO 12647-6:2012/Amd 1:2015 * Graphic technology — Process control for the production of half-tone colour separations, proofs and production prints — Part 6: Flexographic printing — Amendment 1 XZ
TC 131 Fluid power systems
ISO 4393:2015 Fluid power systems and components — Cylinders — Basic series of piston strokes A
ISO 10767-1:2015 Hydraulic fluid power — Determination of pressure ripple levels generated in systems and components — Part 1: Method for determining source flow ripple and source impedance of pumps E
TC 146 Air quality
ISO 17211:2015 Stationary source emissions — Sampling and determination of selenium compounds in flue gas D
TC 157 Non-systemic contraceptives and STI barrier prophylactics
ISO 4074:2015 Natural rubber latex male condoms — Requirements and test methods G
TC 172 Optics and photonics
ISO 8600-1:2015 * Endoscopes — Medical endoscopes and endotherapy devices — Part 1: General requirements C
ISO/TS 18340:2015 * Endoscopes — Trocar pins, trocar sleeves and endotherapy devices for use with trocar sleeves B
TC 181 Safety of toys
ISO 8124-7:2015 * Safety of toys — Part 7: Requirements and test methods for finger paints G
TC 188 Small craft
ISO 12217-1:2015 Small craft — Stability and buoyancy assessment and categorization — Part 1: Non-sailing boats of hull length greater than or equal to 6 m G
ISO 12217-2:2015 Small craft — Stability and buoyancy assessment and categorization — Part 2: Sailing boats of hull length greater than or equal to 6 m H
ISO 12217-3:2015 Small craft — Stability and buoyancy assessment and categorization — Part 3: Boats of hull length less than 6 m G
TC 193 Natural gas
ISO/TR 12748:2015 * Natural Gas — Wet gas flow measurement in natural gas operations H
TC 199 Safety of machinery
ISO 14123-1:2015 Safety of machinery — Reduction of risks to health resulting from hazardous substances emitted by machinery — Part 1: Principles and specifications for machinery manufacturers B
TC 201 Surface chemical analysis
ISO 11775:2015 * Surface chemical analysis — Scanning-probe microscopy — Determination of cantilever normal spring constants D
TC 204 Intelligent transport systems
ISO 14817-1:2015 * Intelligent transport systems — ITS central data dictionaries — Part 1: Requirements for ITS data definitions G
ISO 14817-2:2015 * Intelligent transport systems — ITS central data dictionaries — Part 2: Governance of the Central ITS Data Concept Registry D
ISO/TR 17427-2:2015 * Intelligent transport systems — Cooperative ITS — Part 2: Framework overview E
ISO/TR 17427-3:2015 * Intelligent transport systems — Cooperative ITS — Part 3: Concept of operations (ConOps) for ‚core’ systems H
ISO/TR 17427-4:2015 * Intelligent transport systems — Cooperative ITS — Part 4: Minimum system requirements and behaviour for core systems F
ISO/TR 17427-6:2015 * Intelligent transport systems — Cooperative ITS — Part 6: ‚Core system’ risk assessment methodology D
ISO/TR 17427-7:2015 * Intelligent transport systems — Cooperative ITS — Part 7: Privacy aspects D
ISO/TR 17427-8:2015 * Intelligent transport systems — Cooperative ITS — Part 8: Liability aspects D
ISO/TR 17427-9:2015 * Intelligent transport systems — Cooperative ITS — Part 9: Compliance and enforcement aspects C
ISO/TR 17427-10:2015 * Intelligent transport systems — Cooperative ITS — Part 10: Driver distraction and information display D
ISO/TR 19639:2015 * Electronic fee collection — Investigation of EFC standards for common payment schemes for multi-modal transport services E
ISO 24014-1:2015 Public transport — Interoperable fare management system — Part 1: Architecture G
ISO/TR 24097-2:2015 * Intelligent transport systems — Using web services (machine-machine delivery) for ITS service delivery — Part 2: Elaboration of interoperable web services’ interfaces D
TC 206 Fine ceramics
ISO 13383-1:2012 Fine ceramics (advanced ceramics, advanced technical ceramics) — Microstructural characterization — Part 1: Determination of grain size and size distribution D
ISO 13383-2:2012 Fine ceramics (advanced ceramics, advanced technical ceramics) — Microstructural characterization — Part 2: Determination of phase volume fraction by evaluation of micrographs B
ISO 23145-1:2007 Fine ceramics (advanced ceramics, advanced technical ceramics) — Determination of bulk density of ceramic powders — Part 1: Tap density A
ISO 23145-2:2012 Fine ceramics (advanced ceramics, advanced technical ceramics) — Determination of bulk density of ceramic powders — Part 2: Untapped density B
TC 211 Geographic information/Geomatics
ISO 19150-2:2015 Geographic information — Ontology — Part 2: Rules for developing ontologies in the Web Ontology Language (OWL) H
TC 213 Dimensional and geometrical product specifications and verification
ISO 1938-1:2015 Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 1: Plain limit gauges of linear size E
ISO 16610-30:2015 Geometrical product specifications (GPS) — Filtration — Part 30: Robust profile filters: Basic concepts C
ISO 16610-60:2015 Geometrical product specification (GPS) — Filtration
— Part 60: Linear areal filters — Basic concepts
C
TC 234 Fisheries and aquaculture
ISO 18537:2015 Traceability of crustacean products — Specifications on the information to be recorded in captured crustacean distribution chains D
TC 238 Solid biofuels
ISO 17829:2015 * Solid Biofuels — Determination of length and diameter of pellets A
ISO 18122:2015 Solid biofuels — Determination of ash content A
ISO 18123:2015 Solid biofuels — Determination of the content of volatile matter B
TC 292 Security and resilience
ISO 22301:2012 * Societal security — Business continuity management systems — Requirements D
TMBG Technical Management Board – groups
IWA 15:2015 * Specification and method for the determination of performance of automated liquid handling systems H
CASCO Committee on conformity assessment
ISO/IEC 17050-1:2004 * Conformity assessment — Supplier’s declaration of conformity — Part 1: General requirements A
JTC 1 Information technology
ISO/IEC 25024:2015 * Systems and software engineering — Systems and software Quality Requirements and Evaluation (SQuaRE) — Measurement of data quality F
ISO/IEC TR 29110-3-1:2015 * Systems and software engineering — Lifecycle profiles for Very Small Entities (VSEs) — Part 3-1: Assessment guide F
ISO/IEC TR 29110-3-4:2015 * Systems and software engineering — Lifecycle profiles for Very Small Entities (VSEs) — Part 3-4: Autonomy-based improvement method D
ISO/IEC TR 18781:2015 * Identification cards — Laundry testing of ID Cards A
ISO/IEC TS 18661-3:2015 * Information Technology — Programming languages, their environments, and system software interfaces — Floating-point extensions for C — Part 3: Interchange and extended types G
ISO/IEC TS 18661-4:2015 * Information Technology — Programming languages, their environments, and system software interfaces — Floating-point extensions for C — Part 4: Supplementary functions E
ISO/IEC 19776-3:2015 * Information technology — Computer graphics, image processing and environmental data representation — Extensible 3D (X3D) encodings — Part 3: Compressed binary encoding A
ISO/IEC TR 11801-9903:2015 * Information technology — Generic cabling systems for customer premises — Part 9903: Matrix modelling of channels and links D
ISO/IEC 30129:2015 * Information technology — Telecommunications bonding networks for buildings and other structures F
ISO/IEC 14496-22:2015 * Information technology — Coding of audio-visual objects — Part 22: Open Font Format H
ISO/IEC 15444-5:2015 * Information technology — JPEG 2000 image coding system: Reference software — Part 5: C
ISO/IEC 23008-3:2015 * Information technology — High efficiency coding and media delivery in heterogeneous environments — Part 3: 3D audio H
ISO/IEC TR 23009-3:2015 * Information technology — Dynamic adaptive streaming over HTTP (DASH) — Part 3: Implementation guidelines G
ISO/IEC 18000-63:2015 * Information technology — Radio frequency identification for item management — Part 63: Parameters for air interface communications at 860 MHz to 960 MHz Type C H
ISO/IEC 24770-62:2015 * Information technology — Real-time locating system (RTLS) device performance test methods — Part 62: High rate pulse repetition frequency Ultra Wide Band (UWB) air interface B
ISO/IEC 29167-14:2015 * Information technology — Automatic identification and data capture techniques — Part 14: Crypto suite AES OFB security services for air interface communications E
ISO/IEC 19763-7:2015 * Information technology — Metamodel framework for interoperability (MFI) — Part 7: Metamodel for service model registration E
ISO/IEC 19763-8:2015 * Information technology — Metamodel framework for interoperability (MFI)               — Part 8: Metamodel for role and goal model registration D
ISO/IEC TR 19763-9:2015 * Information technology — Metamodel framework for interoperability (MFI)               — Part 9: On demand model selection C
ISO/IEC 19757-7:2009/Cor 1:2015 * Information technology — Document Schema Definition Languages (DSDL) — Part 7: Character Repertoire Description Language (CREPDL) — Technical Corrigendum 1 free
ISO/IEC 21320-1:2015 * Information technology — Document Container File — Part 1: Core B
ISO/IEC TR 13066-4:2015 * Information technology — Interoperability with assistive technology (AT) — Part 4: Linux/UNIX graphical environments accessibility API D
ISO/IEC 19778-1:2015 * Information technology — Learning, education and training — Collaborative technology — Collaborative workplace — Part 1: Collaborative workplace data model E
ISO/IEC 19778-2:2015 * Information technology — Learning, education and training — Collaborative technology — Collaborative workplace — Part 2: Collaborative environment data model D
ISO/IEC 19778-3:2015 * Information technology — Learning, education and training — Collaborative technology — Collaborative workplace — Part 3: Collaborative group data model C
ISO/IEC 19780-1:2015 * Information technology — Learning, education and training — Collaborative technology — Collaborative learning communication — Part 1: Text-based communication C

 

Kontakt

Imię i nazwisko (wymagane)

Telefon (wymagane)

Adres email (wymagane)

Treść wiadomości

Dane kontaktowe

Siedziba:

os. Strusia 1A, 31-807 Kraków